|Q0001: ||How to identify authentic ASIX USB to LAN products inside?|
|A0001: ||If ASIX USB to LAN drivers cannot work fine on your USB to LAN device, please refer to How to identify authentic ASIX USB to LAN Products document to double check if your USB to LAN device includes a Non-authentic ASIX USB to LAN solution inside or not? If yes, please contact the manufacturer of your USB to LAN device to get proper drivers directly. ASIX DOES NOT GUARANTEE AND PROVIDE ANY SUPPORT FOR THOSE NON-AUTHENTIC ASIX PRODUCTS.|
The KY-88772A USB 2.0 to Fast Ethernet Adapter is a typical non-authentic ASIX USB to LAN product.
|Q0002: ||Where can I obtain the latest AX88760 drivers?|
|A0002: ||The integrated Ethernet Controller of AX88760 is fully compatible with ASIX's AX88772A USB2.0 to 10/100 Fast Ethernet Controller, therefore AX88772A driver can bring up AX88760 Ethernet controller function without any
modification. Please visit the AX88760 Driver Download web page (http://www.asix.com.tw/download.php?sub=driverdetail&PItemID=103) for details. |
|Q0003: ||Are AX88760 Windows drivers qualified by the WHQL compliant certification?|
|A0003: ||Yes, all AX88760/AX88772A Windows 7/Vista/XP 32-bit/64-bit drivers were qualified by Microsoft WHQL certification.|
|Q0004: ||Which AX88760 Windows driver (32-bit or 64-bit) should I download for my Windows system?|
|A0004: ||You can easily download the AX88760/AX88772A Windows 7, Vista or XP 32-bit/64-bit WHQL drivers setup program from AX88760 Driver Download web page (http://www.asix.com.tw/download.php?sub=driverdetail&PItemID=103) and then run the setup program to install a proper AX88760/AX88772A Windows driver on your Windows machine directly. |
|Q0005: ||Why don't ASIX's AX88760 standard drivers work with my AX88760 device?|
|A0005: ||All ASIX's AX88760/AX88772A standard drivers are qualified with ASIX's AX88760/AX88772A demo boards with AX88772A default Vendor ID (0B95h) and Product ID (772Ah). Some of AX88760 manufacturers have their own Vendor ID and Product ID on their AX88760 applications. In this case, ASIX's AX88760 standard drivers will not work with your AX88760 device. Please contact the technical support of your AX88760 device manufacturer to obtain a proper driver.|
|Q0006: ||How can I install AX88760 Linux driver on my Android tablet PC?|
|A0006: ||No, it could not be done by end users. To install AX88760 Linux driver on your Android tablet PC, you have to recompile AX88760 Linux driver source on your target Android tablet platform and then you can install the compiled AX88760 Linux driver on your Android platform. It can only be done by the manufacturer of your Android tablet PC. Please contact the support guys of the manufacturer for further support if necessary.
|Q0007: ||How to capture the VLAN tagged packets on Windows WireShark tool?|
|A0007: ||Please set the "Packet Priority & VLAN" parameter of ASIX USB to LAN Windows drivers to "Packet Priority & VLAN Disable" to capture the VLAN tagged packets on WireShark.|
|Q0008: || Does AX88760 support Windows Surface RT 8.0/8.1 driver?|
|A0008: ||No, AX88760 doesn’t support Windows Surface RT 8.0/8.1 driver.
|Q0009: ||Where can I obtain the latest AX88760 datasheet, reference schematic and other hardware design archives?|
|A0009: ||Please register MyASIX membership (http://www.asix.com.tw/RegLogin.php?mod=thisis) and then download the latest AX88760 datasheet, reference schematic, gerber/PCB layout files and application design note from AX88760 Product web page (http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=103;71;108&PLine=71) directly.|
|Q0010: ||How to open the gerber files of AX88760 demo board?|
|A0010: ||You can open the gerber files of AX88760 demo board by running ORACLE's AutoVue Evaluation Revision tool (30 days evaluation date). Please visit ORACLE's web site (http://www.oracle.com/) for more details.|
|Q0011: ||How to open the PowerPCB PCB layout file of AX88760 demo board?|
|A0011: ||You can open the PowerPCB PCB layout file of AX88760 demo board by running Mentor Graphics PADS Layout Product Evaluation Software (No time limitation but with limited function). Please visit Mentor Graphics' web site (http://www.mentor.com/) for more details.|
|Q0012: ||Can ASIX help me to review my own AX88760 schematic and PCB layout?|
|A0012: ||Yes, please deliver your own AX88760 schematic and PCB layout files to ASIX's Support (email@example.com) for further review before making your own AX88760 PCB board.|
|Q0013: ||Do I need to develop AX88760 drivers by myself?|
|A0013: ||No, the AX88760 already supports available device drivers for most of operating systems such as Windows 7/Vista/XP, Linux, Mac OSX, WinCE/Mobile, etc. Please visit AX88760 Driver Download web page (http://www.asix.com.tw/download.php?sub=driverdetail&PItemID=103) for details.
For some special OS supporting requirements, please contact ASIX's sales (firstname.lastname@example.org) for further support.
|Q0014: ||How can I configure AX88760 at Self-power mode?|
|A0014: ||The AX88760 is a high performance USB 2.0 MTT hub with integrated 10/100 Fast Ethernet controller and it is suitable to implement on those self-power applications such as the embedded system, docking station, etc. AX88760 can be configured to self-power mode by pulling high the PSELF signal.
Please also refer to AX88760 EEPROM User Guide to configure AX88760 EEPROM with proper self-power mode configuration.|
|Q0015: ||What are the specification of 12MHz/25MHz reference crystals of AX88760 demo board?|
|A0015: ||The 12MHz/25MHz crystal signals of AX88760 board should be winthin 12MHz +- 50ppm/25MHz +- 50ppm. Please refer to AX88760 USB Hub/Ethernet Combo Application Design Note for details. |
|Q0016: ||What is the reference Ethernet transformer of the AX88760 demo board?|
|A0016: ||The reference Ethernet transformer on the AX88760 demo board is the Bothhand LU1S041X LF (Turns Ratio 1CT:1CT, Auto-MDIX) single RJ-45 connector module with integrated 10/100 BASE-TX magnetic. Please refer to AX88760 USB Hub/Ethernet Combo Application Design Note for the detailed Ethernet magnetic circuit information. |
|Q0017: ||What kind of EEPROM is supported by AX88760?|
|A0017: ||The AX88760 supports 16-bit mode 93C56 or 93C66 EEPROM.|
|Q0018: ||How do I program the AX88760 EEPROM?|
|A0018: ||AX88760 supports some default settings inside chip hardware to enable it to communicate with USB host controller during enumeration when the AX88760 EEPROM is blank (prior to being programmed). The default settings inside chip facilitate users to update the EEPROM content through a Windows PC during R&D validation process or program a blank EEPROM mounted on target system PCB during manufacturing process. |
ASIX Electronics provides Windows/WinCE/Linux SROM programming tools for users to easily program the Serial EEPROM of AX88760 on a typical Windows/WinCE/Linux platforms. These AX88760 SROM programming tools support to customize the MAC address, Serial Number, Vendor ID and Product ID, etc. for AX88760 based application systems in mass production.
Alternatively, users can pre-program the blank EEPROM on a 3rd Party Universal Programmer before soldering the EEPROM onto the AX88760 application device. You must assign a unique MAC address in the EEPROM for every AX88760 device.
|Q0019: ||Do we need to register our own VID/PID for our AX88760 based application systems or can we use the ASIX's VID/PID?|
|A0019: ||The answers to above questions really depend on user's product applications and target market, which can be different on individual cases. Below gives customers some general guidelines about whether one can use ASIX's VID/PID or one should better register its own one with USB-IF.|
1.Case where it is OK to use ASIX Electronics's VID (0B95h) and PID (772Ah):
You may be able to use ASIX Electronics' VID and PID when your AX88772A/AX88760 based application system can simply work with AX88772A standard drivers provided by ASIX without any modification and you don't have any concern from business and product marketing perspective to use the same VID and PID on your products as ASIX's other customers who are also using ASIX's VID and PID. ASIX Electronics would like to request customers to inform ASIX sales staffs by sending us email at email@example.com beforehand if you would like to use ASIX Electronics VID and PID for your products.
In other words, if your AX88772A/AX88760 based application system requires you to modify AX88772A driver on your own or by ASIX support team, you might have to register your own VID and PID. This can avoid your end customers from going to ASIX web site to download the AX88772A standard driver which may not be suitable to work with the specific AX88772A/AX88760 based application system.
2.Cases requiring you to use your own VID and PID
(1) Your AX88772A/AX88760 based application systems can't work directly with AX88772A standard drivers which ASIX Electronics release on its web site and your target application system (such as USB dongle or docking station) may allow your end customers to update the standalone AX88772A driver by themselves after sales. In that case, you MUST assign your own unique VID and PID for your AX88772A/AX88760 based devices.
(2) For brand name products, you probably don't want your AX88772A/AX88760 based devices to become compatible with other company's AX88772A/AX88760 based devices. In this case, you should consider assigning your own unique VID and PID for your AX88772A/AX88760 based devices.
You can register your own VID from USB Implementers Forum, Inc. and define the PID based on your company rules.
|Q0020: ||How do I register a Vendor ID from USB-IF?|
|A0020: ||If you are a new USB product developer looking to get a Vendor ID for your company, you can register a Vendor ID from USB Implementers Forum, Inc. Please visit the USB-IF web site (http://www.usb.org/developers/vendor/) for details.|
|Q0021: ||Do I have to assign a unique MAC address to every AX88760 based devices?|
|A0021: ||Yes, every Ethernet device must have a unique MAC address. Users should always assign a unique MAC address in the AX88760 EEPROM for every AX88760 based devices.|
|Q0022: ||How do I register a MAC/Ethernet address from IEEE-SA?|
|A0022: ||You must first have an OUI or an IAB, to which you then append 24 or 12 bits respectively, in a way that makes the resulting 48-bit number unique, i.e., your 24 or 12 bits must be unique within your organization, which will require coordination among all the users of your organization's OUI or IAB. Please visit the IEEE-SA web site (http://standards.ieee.org/regauth/registry_OUI.html) for details.|
|Q0023: ||Do I have to assign a unique serial number to every AX88760 based device?|
|A0023: ||No, it depends on the real requirement of your AX88760 target application. If users need to install more than one AX88760 based devices on your target application, you should assign a different serial number in the EEPROM for every AX88760 device.|
If your target application always uses one AX88760 device, you can consider assigning the same serial number in the EEPROM for every AX88760 device for easy maintenance in mass production, especially if you plan to use a Windows PC to test AX88760 based devices repeatedly during mass production test.
|Q0024: ||Did the AX88760 pass the USB-IF compliant certification?|
|A0024: ||Yes, AX88760 demo board was certified by USB-IF. |